Display settingsLink
Accessible from menu Display Settings
Preferred unitsLink
It allows you to select units for measurement to specify various distance, speed and altitude. You could see this in the mobile app and your display.
Options
- Metric (km, m, kph=km/h)
- Imperial (mi, ft, mi/h)
Secondary unitLink
It controls which value to show on the display main screen for the secondary unit.
- Power, W
- Current, A
- Efficiency, wh/distance
ProtocolLink
For each protocol type there are two options, one normal and one Rx/Tx Swap. The last one is to help when the communications wires are inverted.
Info
When set to Auto the display will try to autodetect the protocol at the next startup.
Options
- Auto
- Bafang
- Lishui
- Kunteng
- Tonseng
- ASI
- Bafang Rx/Tx Swap
- Lishui Rx/Tx Swap
- Kunteng Rx/Tx Swap
- Tonseng Rx/Tx Swap
- ASI Rx/Tx Swap
Reset tripLink
It controls when the current trip is reset on the display. If Manually selected, the trip will reset only when requested from the Dashboard page. When selected At start-up the trip will reset after every power cycle but keeps the old trip information so it can be downloaded by the app until bike starts to move.
Options
- Manually
- At start-up
ImmobilizerLink
No LockLink
Default behavior, no action taken.
Locked Level 0 (connect with app to unlock)Link
Display will always start locked in assist level 0. You have to connect with the mobile app to unlock to be able to change the assist level or mode profile.
This is intended to cut-off the motor until connected with the mobile app. This setting will also be set if display is locked from dashboard and then power off but it has to be expressly disabled from settings (on dashboard can be disabled only temporary).
Road restrictLink
Option to inhibit changing profile from Road to OffRoad with the M button on the display.
If set to Yes you can only change profile from OffRoad to Road and based on the option use the mobile app for both ways or also the display when the app is connected.
Options are:
- No
- Yes (Change modes only from app)
- Yes (Change modes from the display when the app is connected)
Startup with RoadLink
Decides if the display should always start with the Road profile.
Options are No or Yes.
PowerOffLink
The time after which the display should power off.
Options
- Never
- After 5 minutes
- After 2 hours
- After 10 hours
Mode LabelsLink
The labels used on the display to identify the current profile settings.
Options
- Road/OffRoad
- Eco/Support
Assist LevelsLink
The number of assist levels to be used when using Up and Down buttons. Each option also includes assist level 0.
Attention
Keep in mind that when you select lower than 9 assist levels, EggRider uses internally the levels beween () for pages like power levels or for the bafang basic assist levels. This is to allow changing the number of assist levels witouth altering the power levels.
- 3 - [0, 1(1), 2(5), 3(9)]
- 5 - [0, 1(1), 2(3), 3(5), 4(7), 5(9)]
Options are 9, 3 and 5
Keep headlight at startupLink
This is a convenient feature to keep the headlight as it was before shutting down.
Options are No or Yes.
Mode button press functionLink
Option to change the short and long press functionality of the M button.
Options
- Short - Mode Change / Long - Stats
- Short - Stats / Long - Mode Change
Bafang switch modeLink
The Road/OffRoad mode switch behavior for bafang controllers.
Only live dataLink
Consists in switching only between Max speed Road and Max speed OffRoad settings from the Display Settings page
Live data and settingsLink
Consists of switching between the Max speed Road and Max speed OffRoad setting from the Display settings page plus the relative Road/OffRoad mode for the Bafang Basic, Bafang Pedal, Bafang Throttle profile settings.
Warning
If you are an unexperienced user we highly recommend using Only live data setting until you get familiarised with the bafang settings.
Max speed (km/h)Link
Determines the speed limits for Road and OffRoad. This values can be overwritten by the specific bike/controller settings.
Wheel sizeLink
Offers some predefined Rim + Tire options to populate Wheel circumference with the right value.
Info
The Wheel size drop down is just a helper with predefined values for Wheel circumference. It is normal to go back to Select after the app is restarted.
Wheel circumference (mm)Link
This value is used to calculate the speed. Please use rim + tire value for this setting.
The following links provide comprehensive resources for determining the wheel circumference Wheel size math or Cyclecomputer calibration
Tip
If you think the speed measurement is not precise, you can use this field as a factor to increase or decrease your speed measurement.
BATTERY SETTINGSLink
EggRider has up to 3 battery profiles. You can use these profiles to track stats independently if you have more than one battery.
Please be sure you are setting at least the battery selected profile correctly. You can leave the other battery profiles as they are by default if not used.
To maximize the battery percentage precision, please set the following fields correctly.
Battery usedLink
Represents the battery profile to be used.
Options are 1st, 2nd and 3rd
Battery voltageLink
Offers some predefined values to populate the Voltage 0% and 100%.
Options are 24V, 36V, 48V, 52V, 72V.
Attention
Never connect EggRider to a battery bigger than 52V. EggRider display works up to 60V when directly connected. With certain controllers we can overcome this limit by connecting to a 12V output.
Info
Battery voltage drop down is just a helper with predefined values for Voltage 0% and Voltage 100%. It is normal to go back to Select.
Voltage 0%Link
The empty battery voltage.
This field has a resolution of 0.01 V.
Voltage 100%Link
The full battery voltage.
This field has a resolution of 0.01 V.
CapacityLink
The capacity of the battery measured in ampere hour (Ah).
This field has a resolution of 0.01 Ah.